LOREADA 04C133062D 802010407001 Throttle Body For VW Up! Polo Mii SEAT Ibiza IV Mii Skoda Citigo Fabia III 1.0 MPI 2011-2020 OEM Quality

Throttle Body for VW / Seat / Skoda 1.0 MPI (2011–2020)

OE Numbers: 04C133062D / 04C 133 062 D / 802010407001

Direct OEM Replacement | 12+24 Month Warranty | 100% Factory Tested

Vehicle Fitment – Compatible with:

⚠️ Important: This throttle body is designed for 1.0 MPI naturally aspirated engines (CHYA / CHYB). Not compatible with 1.0 TSI turbocharged engines. Please verify your original OE number before ordering. The suffix "D" indicates compatibility with non-turbo MPI engines.-

OE Cross Reference – Match with your original part:

ℹ️ Magneti Marelli is the Original Equipment manufacturer for this throttle body. The 802010407001 number corresponds to the Magneti Marelli OEM part.-

Technical Specifications

ℹ️ This throttle body is supplied without gasket/seal – a new mounting gasket is strongly recommended for proper sealing.-

Product Highlights

✅ OE Fitment – Developed to strict OEM standards. Direct replacement – no wiring modification required.
✅ Genuine OEM Quality – Manufactured to Magneti Marelli specifications, the Original Equipment supplier for VAG.
✅ High Performance – Motor response time ≤ 50 ms for precise intake control, smooth acceleration, and improved throttle sensitivity.
✅ Reliability – Built-in dual redundant position sensors prevent idle fluctuations, hunting, and false error codes.
✅ Rigorous Testing – 100% factory-tested for thermal cycling, airtightness, and full-stroke angle calibration.
✅ Standard Compliance – Meets ISO 16750 environmental standards for automotive electrical/electronic equipment.
✅ 1.0 MPI Optimized – Specifically engineered for VAG 1.0 MPI naturally aspirated engines (CHYA/CHYB), ensuring proper air/fuel mixture for smooth idle and optimal fuel economy.
✅ Plug & Play – Exact match in dimensions, connector pinouts (6-pin), and mounting pattern.
✅ Wide Application – Compatible with multiple VAG models including Up!, Polo, Mii, Ibiza, Citigo, and Fabia.

Common Symptoms of a Failing Throttle Body (1.0 MPI)

• Unstable idle, "hunting," or engine stalling at stops

• Hesitation or flat spot during acceleration

• Check Engine Light (CEL) – common DTCs: P0638, P0697, P2100, P2119, P2120, P2127

• Poor throttle response / delayed acceleration

• Reduced power / limp mode

• Rough running

• Poor fuel economy

*These symptoms are frequently reported for high-mileage 1.0 MPI vehicles when the throttle body components wear out or carbon buildup occurs.-*

Installation & Adaptation Tips

IMPORTANT: After replacing the Electronic Throttle Body (ETB) on VAG 1.0 MPI engines, a throttle self-learning / idle relearn procedure is REQUIRED.

Step-by-Step Procedure:

For VAG 1.0 MPI: The above procedure typically works. If issues persist, use a professional diagnostic scanner (e.g., VCDS / VAG-COM) to perform "Throttle Body Alignment" (Basic Settings Group 060 or 098 in Engine module). After replacement, it may take a few drive cycles for the ECU to fully adapt to the new throttle body.

Packing List

• Electronic Throttle Body Unit (OEM quality) × 1

• (Gasket/seal not included – purchase separately)

• Warranty Card / Quality Certificate × 1

• (Optional: Screws / Connector protector – may vary by batch)

How to Ensure You Get the Correct Part

1. Confirm your vehicle is equipped with the 1.0 MPI naturally aspirated engine (engine codes: CHYA / CHYB). Not compatible with 1.0 TSI turbo engines.

2. Check your original part number on the existing throttle body – look for 04C133062D.

3. Verify the connector has 6 pins (OEM specification for this application).

4. Note that 04C133062 (without D suffix) is an earlier revision – verify compatibility before ordering.

5. Contact us with your VIN or a photo of your original part if unsure.

⚠️ Important: The throttle body is supplied without gasket/seal. A new mounting gasket is strongly recommended for proper sealing and to prevent vacuum leaks. Purchase gasket separately.

After-Sales & Disclaimer

• Pre-installation check: Inspect the throttle body for any defects. Verify the OE number and connector type (6-pin) before installation. A new gasket is required – not included.

• Compatibility: This throttle body is for 1.0 MPI naturally aspirated engines ONLY (CHYA / CHYB). It will NOT fit 1.0 TSI turbocharged engines, 1.2L, 1.4L, or diesel engines.

• Gasket requirement: A new mounting gasket is strongly recommended and must be purchased separately.

• Professional installation recommended: While installation is straightforward, proper adaptation is critical. If you are not comfortable performing the relearn procedure, professional installation is recommended.

• Warranty: This product carries a 12-month warranty against manufacturing defects. The motor and sensors are covered for 24 months.

🛠️ Quick Reference Card (for Print/Inclusion)